A simple kinetic analysis of syngas during steam hydrogasification of biomass using a novel inverted batch reactor with instant high pressure feeding.

A newly designed inverted batch reactor equipped with a pressure-driven feeding system was built for investigating the kinetics of syngas during the steam hydrogasification (SHR) of biomass. The system could instantly load the feedstock into the reactor at high temperature and pressure, which simulated the way to transport the feedstock into a hot and pressurized gasifier. Experiments were conducted from 600°C to 700°C. The inverted reactor showed very high heating rate by enhancing the carbon conversion and syngas production. The kinetic study showed that the rates of CH4, CO and CO2 formation during SHR were increased when the gasification temperature went up. SHR had comparatively lower activation energy for CH4 production. The activation energies of CH4, CO and CO2 during SHR were 42.8, 51.8 and 14kJ/mol, respectively.

Vehicle specific power approach to estimating on-road NH3 emissions from light-duty vehicles.

NH3 emissions from motor vehicles have been the subject of a number of recent studies due to their potential impact on ambient particulate matter (PM). Highly time-resolved NH3 emissions can be measured and correlated with specific driving events utilizing a tunable diode laser (TDL). It is possible to incorporate NH3 emissions with this new information into models that can be used to predict emissions inventories from vehicles. The newer generation of modal models are based on modal events, with the data collected at second-by-second time resolution, unlike the bag-based emission inventory models such as EMFAC and MOBILE. The development of an NH3 modal model is described in this paper. This represents one of the first attempts to incorporate vehicle NH3 emissions into a comprehensive emissions model. This model was used in conjunction with on-road driving profiles to estimate the emissions of SULEV, ULEV, and LEV vehicles to be 9.4 +/- 4.1, 21.8 +/- 5.2, and 34.9 +/- 6.0 mg/mi, respectively. We also implement this new NH3 model to predict and evaluate the NH3 emission inventory in the South Coast air basin (SoCAB).

Emission rates of particulate matter and elemental and organic carbon from in-use diesel engines.

Elemental carbon (EC), organic carbon (OC), and particulate matter (PM) emission rates are reported for a number of heavy heavy-duty diesel trucks (HHDDTs) and back-up generators (BUGs) operating under real-world conditions. Emission rates were determined using a unique mobile emissions laboratory (MEL) equipped with a total capture full-scale dilution tunnel connected directly to the diesel engine via a snorkel. This paper shows that PM, EC, and OC emission rates are strongly dependent on the mode of vehicle operation; highway, arterial, congested, and idling conditions were simulated by following the speed trace from the California Air Resources Board HHDDT cycle. Emission rates for BUGs are reported as a function of engine load at constant speed using the ISO 8178B Cycle D2. The EC, OC, and PM emission rates were determined to be highly variable for the HHDDTs. It was determined that the per mile emission rate of OC from a HHDDT in congested traffic is 8.1 times higher than that of an HHDDT in cruise or highway speed conditions and 1.9 times higher for EC. EC/OC ratios for BUGs (which generally operate at steady states) and HHDDTs show marked differences, indicating that the transient nature of engine operation dictates the EC/OC ratio. Overall, this research shows that the EC/OC ratio varies widely for diesel engines in trucks and BUGs and depends strongly on the operating cycle. The findings reported here have significant implications in the application of chemical mass balance modeling, diesel risk assessment, and control strategies such as the Diesel Risk Reduction Program.

Development and application of a mobile laboratory for measuring emissions from diesel engines. 1. Regulated gaseous emissions.

Information about in-use emissions from diesel engines remains a critical issue for inventory development and policy design. Toward that end, we have developed and verified the first mobile laboratory that measures on-road or real-world emissions from engines at the quality level specified in the U.S. Congress Code of Federal Regulations. This unique mobile laboratory provides information on integrated and modal regulated gaseous emission rates and integrated emission rates for speciated volatile and semivolatile organic compounds and particulate matter during real-world operation. Total emissions are captured and collected from the HDD vehicle that is pulling the mobile laboratory. While primarily intended to accumulate data from HDD vehicles, it may also be used to measure emission rates from stationary diesel sources such as back-up generators. This paper describes the development of the mobile laboratory, its measurement capabilities, and the verification process and provides the first data on total capture gaseous on-road emission measurements following the California Air Resources Board (ARB) 4-mode driving cycle, the hot urban dynamometer driving schedule (UDDS), the modified 5-mode cycle, and a 53.2-mi highway chase experiment. NOx mass emission rates (g mi(-1)) for the ARB 4-mode driving cycle, the hot UDDS driving cycle, and the chase experimentwerefoundto exceed current emission factor estimates for the engine type tested by approximately 50%. It was determined that congested traffic flow as well as "off-Federal Test Procedure cycle" emissions can lead to significant increases in per mile NOx emission rates for HDD vehicles.

Development and application of a mobile laboratory for measuring emissions from diesel engines. 2. Sampling for toxics and particulate matter.

Limited data are available on the emission rates of speciated volatile and semivolatile organic compounds, as well as the physical and chemical characteristics of fine particulate matter (PM) from mobile, in-use diesel engines operated on the road. A design for the sampling of these fractions and the first data from in-use diesel sources are presented in this paper. Emission rates for carbonyls, 1,3-butadiene, benzene, toluene, xylene, PM, and elemental and organic carbon (EC and OC) are reported for a vehicle driven while following the California Air Resources Board (ARB) four-mode heavy heavy-duty diesel truck (HHDDT) cycle and while transiting through a major transportation corridor. Results show that distance specific emission rates are substantially greater in congested traffic as compared with highway cruise conditions. Specifically, emissions of toxic compounds are 3-15 times greater, and PM is 7 times greater under these conditions. The dependence of these species on driving mode suggests that health and source apportionment studies will need to account for driving patterns in addition to emission factors. Comparison of the PM/NOx ratios obtained for the above tests provides insight into the presence and importance of "off-cycle" emissions during on-road driving. Measurements from a stationary source (operated and tested at constant engine speed) equipped with an engine similar to that in the HHDDT yielded a greater understanding of the relative dependence of emissions on load versus engine transients. These data are indicative of the type of investigations made possible by the development of this novel laboratory.

Investigation of NH3 emissions from new technology vehicles as a function of vehicle operating conditions.

The objective of this study was to measure ammonia (NH3) emissions from modern technology vehicles since information is scarce aboutthis importantsource of particulate matter (PM) precursors. Test variables included the emission level to which the vehicle was certified, the vehicle operating conditions, and catalyst age. Eight vehicles with low-emission vehicle (LEV) to super-ultralow-emission vehicle (SULEV) certification levels were tested over the Federal Test Procedure (FTP75), a US06 cycle, a hot running 505, a New York City Cycle (NYCC), and a specially designed Modal Emissions Cycle (MEC01v7) using both as-received and bench-aged catalysts. NH3 emissions in the raw exhaust were measured by tunable diode laser (TDL) absorption spectroscopy. The results show that NH3 emissions depend on driving mode and are primarily generated during acceleration events. More specifically, high NH3 emissions were found for high vehicle specific power (VSP) events and rich operating conditions. For some vehicles, NH3 emissions formed immediately after catalyst light-off during a cold start.

The effects of repairs on tailpipe emissions for on-board diagnostics II-equipped vehicles with the malfunction indicator light illuminated.

A total of 77 On-Board Diagnostics II (OBDII)-equipped vehicles with illuminated malfunction indicator lights (MILs) and non-evaporative codes were tested before and after repair. The test cycles included the Federal Test Procedure (FTP), IM240, and steady-state cycles. A total of 17 vehicles were found with emissions greater than 1.5 times their respective FTP emissions standards. Repair of these vehicles resulted in dramatic reductions in overall emissions for all the cycles. A majority of the remaining vehicles were found to have emissions below the certification standard for the FTP both before and after repair. Repairs for the vehicles with emissions <1.5 times the standard resulted in some smaller but quantifiable emission reductions over the FTP and IM240 but larger reductions over the steady-state driving tests. Misfires, bad oxygen sensors, and exhaust gas recirculation (EGR) problems were the most common non-evaporative causes for triggering the MIL. The results show some fundamental differences between identifying malfunctioning vehicles using OBDII as opposed to more traditional dynamometer tests. In particular, for many systems, OBDII identifies components that are operating outside their design specification rather than for a specific emissions threshold.

Effects of biodiesel blends and Arco EC-diesel on emissions from light heavy-duty diesel vehicles.

Chassis dynamometer tests were performed on seven light heavy-duty diesel trucks comparing the emissions of a California diesel fuel with emissions from four other fuels: ARCO emissions control diesel (EC-D) and three 20% biodiesel blends (one yellow grease and two soy-based). The EC-D and the yellow grease biodiesel blend both showed significant reductions in total hydrocarbons (THC) and carbon monoxide (CO) emissions over the test vehicle fleet. EC-D also showed reductions in particulate matter (PM) emission rates. NOx emissions were comparable for the different fuel types for most of the vehicles tested. The soy-based biodiesel blends showed smaller emissions differences over the test vehicles, including some increases in PM emissions. This is somewhat in contrast to previous studies that have shown larger reductions in THC, CO, and PM for biodiesel blends. The possible influence of different fuels, fuel properties, and engine load on emissions is also discussed.

Population Density, Particulate Emission Characterization, and Impact on the Particulate Inventory of Smoking Vehicles in the South Coast Air Quality Management District.

The impact of high-particulate-emission vehicles on the total light-duty vehicle particulate emission inventory in the South Coast Air Quality Management District (SCAQMD) has been estimated by an analysis of the SCAQMD's CUT-SMOG database, a field survey of smoking vehicles, and particulate emissions testing of representative smoking vehicles. The field study, carried out at 61 sites throughout the SCAQMD, showed that 1.11%-1.75% of the vehicles in the light-duty fleet emit visible smoke. This fleet of smoking vehicles is composed mainly of older vehicles, 8 to 18 years of age. Particulate emission testing of 23 smoking vehicles gave an average Federal Test Procedure (FTP) weighted emission rate of 399 mg/mi with a range of 64-2,323 mg/mi, while the average IM240 emission rate was 346 mg/mi, with a range from 13-1,807 mg/mi. The contribution of light-duty smoking vehicles to the particulate emissions inventory in the SCAQMD is estimated to be 0.51-0.81 tons per day.